Can You Install ceramic Tile Over Concrete?

Independent Tiling Company.



tiling company

I have removed all existing flooring as well as installed a brand-new 3/4 ″ plywood after coating it with water sealer. I purchased a residence as well as disliked the sheet vinyl in the washroom, and also 6 layers of wallpaper!


Where do you start when tiling a bath?

Apply a layer of adhesive on top of the old tiles as well. Then, comb the adhesive in one direction – don't get fancy here. Your tiles will stick better if the adhesive is combed in one direction in parallel lines without swirls. Once you evenly apply the adhesive it is time to lay your tiles.


You need to eliminate and replace any rotten timber before tiling. Ensure you have a great solid plywood subfloor, then screw down a layer of 1/2 ″ cement backer board in addition to it to act as a base for the floor tile. As a result of issues with seasonal timber motion and cupping, placing 1/4 ″ cement backer board straight in addition to a solid timber subfloor is not recommended. A far better option, if you can not take the wood up, is to put a layer of plywood in addition to the wood floor covering, followed by concrete backer board as well as tile.


Since I have actually strolled on the "crunchy" spots quite a bit, they have actually reduced considerably. I think of the dried out compound has gotten into smaller sized granules and settled, therefore causing less of the problem I got upon first strolling on it.


flooring dublin Tile Setup Cost


I think I didn't blend in sufficient water in the adhesive concrete mix. I was going for a "peanut butter" consistency, but by the time I obtained it on the flooring it was most likely also completely dry. When I troweled it accross the timber it would certainly sometimes not also stick, yet simply slide over without "damping" the board.


I removed 2 layers of sheet vinyl, a slim sheet of timber, and also am now obtaining the fragment board. Underneath every one of this is the initial oak hardwoods-- it was initially part of an area that was converted into a bathroom. At the hardwood degree the bathroom is degree with the hallway. What would certainly I need to place on top of the woods prior to tiling?


Now That We have actually Discussed The Most Proper Instructions To Lay Your Timber Flooring, Let's Currently Think about ...


Do you need underlayment for tile?

In showers, the movement joints are all the corners, vertically and horizontally. But it isn't flexible enough to stay intact where a shower pan or tub meets surrounding walls. Nor is grout the right material for filling the corner joints on the walls. For these spaces, the right material is caulk.


I filled up the openings with timber filler, stained and varnished the threshold and also it looks stunning. In prep for ceramic tile work in my little 4 × 5 restroom, I just recently put down backer board over a new layer of plywood subfloor. I put adhesive mortar cement under the concrete backer board then screwed the board down. When walking on parts of the backer board, the following day I obtained a crunchy audio.



  • In terms of monitoring, we stay operational as well as fully offered using both electronic and also telephonic means.
  • We have thought about how our physical jobs can be carried out whilst observing the 2m range need and will only undertake tasks where this can be attained.
  • It is not prepared for that conditions will emerge where it ends up being difficult to keep the 2m range guideline.
  • In the 29 years Geoff stood at the helm below at Plunkett's there was little bit he did not efficiently achieve and navigate.

Damp Ceramic Tile Saw Or Break Ceramic Tile Cutter


1/4 ″ cement board was than glued and also screwed over the plywood. Then a 12 ″ x 12 ″ mosaic floor tile on a mesh backing was the ceramic tile we made use of. The flooring looks fantastic and also there have been no problems in all. The only issue we had was there was a 1-1/4 ″ distinction in the flooring elevation of the restroom and my hallway which has the usual long-leaf yearn tongue and groove flooring. We required a threshold that would certainly make up the flooring height distinctions but there was absolutely nothing on the marketplace that you might just acquire.


Is there any kind of advantage or added prep needed when utilizing these products with the radiant floor heating mats? Likewise, is there something added I'm supposed to do to waterproof this stuff? I maintain seeing that mentioned in online forums and also I'm not truly certain exactly how that applies. I was wondering if I ought to water resistant then place thinset and connect concrete board with the thinset and also or nails that experience concrete, then the floor tile.


Or should I rip the hardwood flooring out as well and after that placed cementboard down? I have time and energy, I just need to know the best route to take.


Assist Obtaining Fingernail Polish Off Floor Tile Cement



Would certainly it be advisable to eliminate among the plywood and install the cement floor prior to setting the tiles? One service provider is suggesting that we ceramic tile right on top of the plastic floor which I am not also keen on doing. The kitchen area presently has plastic floor covering on top of wood floor covering in addition to of wood sub-flooring. I have reviewed that cement backboard is the way to go when laying floor tiles, but I'm anxious that it will add far too much height to the kitchen area floor contrasted to the floors of surrounding areas.



Hi, My spouse as well as I stay in a home that my Daddy and also I developed ourselves three years earlier. We hadn't quite finished your house (trim job, kitchen area counter tops, etc. still to do) when we relocated and for the last three years our bathroom flooring has actually just been the plywood subfloor. We are preparing yourself to take down tile as well as a under flooring heater. I have actually been attempting to choose whether to use Hardibacker or cement board over the plywood.


It would rely on what center the joists get on, the density and also material utilized for the subfloor, and also the problem it is in. If you can disperse it by strolling on it in between the joists, you most likely should include an additional layer of 1/2 ″ to 5/8 ″ plywood in addition to the existing subfloor, prior to applying the cement board. I have 2 layers of plywood under the present plastic floor covering.



That trouble was fixed by utilizing the nicest-looking, straightest framing 2 × 4 I could find. My handyman took the door molding off, reduced the 2 × 4 and molding to fit the opening and afterwards developed a lip to fit over the floor tile. We then beveled the leading sides-- one bevel on the restroom side as well as one bevel on the corridor side. He made use of 3 ″ screws to screw the change threshold to the timber floor below and additionally used a countersink drill bit so the screws wouldn't show.


floor tilers